PIX防火墙配置A/S故障切换
作者：互联网
PIX防火墙配置A/S故障切换
1、基本命令
failover
show failover
failover lan enable
failover lan interface zwish e2
failover interface ip zwish 172.17.9.1 255.255.255.0 standby 172.17.9.2
failover lan unit primary
failover lan unit secondary
2、示例
拓扑：
1）配置命令
PIX1主防火墙配置：
pixfirewall> en
Password:
pixfirewall# show mode
Security context mode: single
pixfirewall# show version
Cisco PIX Security Appliance Software Version 7.2(2)
Compiled on Wed 22-Nov-06 14:16 by builders
System image file is "Unknown, monitor mode tftp booted image"
Config file at boot was "startup-config"
pixfirewall up 20 secs
Hardware: PIX-525, 128 MB RAM, CPU Pentium II 1 MHz
Flash E28F128J3 @ 0xfff00000, 16MB
BIOS Flash AM29F400B @ 0xfffd8000, 32KB
0: Ext: Ethernet0 : address is 00ab.bffb.c400, irq 9
1: Ext: Ethernet1 : address is 00ab.bffb.c401, irq 11
2: Ext: Ethernet2 : address is 00ab.bffb.c402, irq 11
3: Ext: Ethernet3 : address is 0000.abfe.0f03, irq 11
4: Ext: Ethernet4 : address is 0000.ab52.1504, irq 11
The Running Activation Key is not valid, using default settings:
Licensed features for this platform:
Maximum Physical Interfaces : 6
Maximum VLANs : 25
Inside Hosts : Unlimited
Failover : Disabled
VPN-DES : Disabled
VPN-3DES-AES : Disabled
Cut-through Proxy : Enabled
Guards : Enabled
URL Filtering : Enabled
Security Contexts : 0
GTP/GPRS : Disabled
#发现这里没有激活防火墙，不支持failover
pixfirewall# activ
pixfirewall# activation-key 0xd2390d2c 0x9fc4b36d 0x98442d99 0xeef7d8b1
The following features available in flash activation key are NOT
available in new activation key:
Failover is different.
flash activation key: Restricted(R)
new activation key: Unrestricted(UR)
Proceed with update flash activation key? [confirm]
The following features available in running activation key are NOT
available in new activation key:
Failover is different.
running activation key: Restricted(R)
new activation key: Unrestricted(UR)
WARNING: The running activation key was not updated with the requested key.
The flash activation key was updated with the requested key, and will
become active after the next reload.
#激活后开始配置pix1主防火墙，（这里做的时候没有使用hostname命名，不过最好有这么一步后面才有对比）
pixfirewall# conf t
pixfirewall(config)# int e0
pixfirewall(config-if)# nameif inside
INFO: Security level for "inside" set to 100 by default.
pixfirewall(config-if)# ip address 192.168.1.1 255.255.255.0
pixfirewall(config-if)# no sh
pixfirewall(config-if)# int e1
pixfirewall(config-if)# nameif outside
INFO: Security level for "outside" set to 0 by default.
pixfirewall(config-if)# ip address 13.0.1.1 255.255.255.0
pixfirewall(config-if)# no sh
pixfirewall(config-if)# int e2
pixfirewall(config-if)# ip address 172.17.9.1 255.255.255.0
pixfirewall(config-if)# no sh
pixfirewall(config-if)# exit
pixfirewall(config)# static (inside,outside) 13.0.1.10 192.168.1.3
#允许13.0.1.3 telnet 13.0.1.10（192.168.1.3）
pixfirewall(config)# access-list test1 permit tcp host 13.0.1.3 host 13.0.1.10 eq telnet
pixfirewall(config)# access-group test1 in int outside
###后面发现使用telnet对比主备防火墙切换不明显，就想换一下ping来对比，这是额外添加的规则###
pixfirewall(config)# access-list test1 extended permit icmp host 13.0.1.10 host 13.0.1.4 echo-reply
pixfirewall(config)# access-list test1 extended permit icmp host 13.0.1.4 host 13.0.1.10 echo
#设置故障切换ip的步骤，这里其实可以与上面的配置接口ip一起做了
pixfirewall(config-if)# int e0
pixfirewall(config-if)# ip address 192.168.1.1 255.255.255.0 standby 192.168.1$
pixfirewall(config-if)# int e1
pixfirewall(config-if)# ip address 13.0.1.1 255.255.255.0 standby 13.0.1.2
pixfirewall(config-if)# exit
pixfirewall(config)# failover lan enable
pixfirewall(config)# failo
pixfirewall(config)# failover lan interface zwish e2
INFO: Non-failover interface config is cleared on Ethernet2 and its sub-interfaces
pixfirewall(config)# failover interface ip zwish 172.17.9.1 255.255.255.0 standby 172.17.9.2
pixfirewall(config)# failover lan unit
pixfirewall(config)# failover lan unit pri
pixfirewall(config)# failover lan unit primary
pixfirewall(config)# failover
pixfirewall(config)# show failover
Failover On
Cable status: N/A - LAN-based failover enabled
Failover unit Primary
Failover LAN Interface: zwish Ethernet2 (up)
Unit Poll frequency 15 seconds, holdtime 45 seconds
Interface Poll frequency 5 seconds, holdtime 25 seconds
Interface Policy 1
Monitored Interfaces 2 of 250 maximum
Version: Ours 7.2(2), Mate Unknown
Last Failover at: 07:26:16 UTC Apr 24 2020
This host: Primary - Negotiation
Active time: 0 (sec)
Interface inside (192.168.1.1): Normal (Waiting)
Interface outside (13.0.1.1): Normal (Waiting)
Other host: Secondary - Not Detected
Active time: 0 (sec)
Interface inside (192.168.1.2): Unknown (Waiting)
Interface outside (13.0.1.2): Unknown (Waiting)
Stateful Failover Logical Update Statistics
Link : Unconfigured.
pixfirewall(config)# .
No Response from Mate
Failover LAN Failed
No switchover
Failover LAN became OK
Switchover enabled
Beginning configuration replication: Sending to mate.
End Configuration Replication to mate
#这里可能需要等一下，再来一次show failover，可以看到主防火墙配置成功
pixfirewall(config)# show failover
Failover On
Cable status: N/A - LAN-based failover enabled
Failover unit Primary
Failover LAN Interface: zwish Ethernet2 (up)
Unit Poll frequency 15 seconds, holdtime 45 seconds
Interface Poll frequency 5 seconds, holdtime 25 seconds
Interface Policy 1
Monitored Interfaces 2 of 250 maximum
Version: Ours 7.2(2), Mate 7.2(2)
Last Failover at: 07:46:05 UTC Apr 24 2020
This host: Primary - Active
Active time: 135 (sec)
Interface inside (192.168.1.1): Normal
Interface outside (13.0.1.1): Normal
Other host: Secondary - Standby Ready
Active time: 0 (sec)
Interface inside (192.168.1.2): Normal
Interface outside (13.0.1.2): Normal
Stateful Failover Logical Update Statistics
Link : Unconfigured.
pixfirewall(config)#
PIX2备份防火墙配置：
pixfirewall> en
Password:
pixfirewall# conf t
pixfirewall(config)# int e0
pixfirewall(config-if)# nameif inside
INFO: Security level for "inside" set to 100 by default.
pixfirewall(config-if)# ip address 192.168.1.2 255.255.255.0
pixfirewall(config-if)# no sh
pixfirewall(config-if)# int e1
pixfirewall(config-if)# nameif outside
INFO: Security level for "outside" set to 0 by default.
pixfirewall(config-if)# ip address 13.0.1.2 255.255.255.0
pixfirewall(config-if)# no sh
pixfirewall(config-if)# int e2
pixfirewall(config-if)# ip address 172.17.9.2 255.255.255.0
pixfirewall(config-if)# no sh
pixfirewall(config-if)# exit
pixfirewall(config)# failover lan enable
pixfirewall(config)# failover lan interface zwish e2
INFO: Non-failover interface config is cleared on Ethernet2 and its sub-interfaces
pixfirewall(config)# failover interface ip zwish 172.17.9.1 255.255.255.0 stan$
pixfirewall(config)# failover lan unit sec
pixfirewall(config)# failover lan unit secondary
pixfirewall(config)# failover
pixfirewall(config)# show failover
Failover On
Cable status: N/A - LAN-based failover enabled
Failover unit Secondary
Failover LAN Interface: zwish Ethernet2 (up)
Unit Poll frequency 15 seconds, holdtime 45 seconds
Interface Poll frequency 5 seconds, holdtime 25 seconds
Interface Policy 1
Monitored Interfaces 2 of 250 maximum
Version: Ours 7.2(2), Mate 7.2(2)
Last Failover at: 07:40:21 UTC Apr 24 2020
This host: Secondary - Negotiation
Active time: 0 (sec)
Interface inside (192.168.1.2): No Link (Waiting)
Interface outside (13.0.1.2): No Link (Waiting)
Other host: Primary - Active
Active time: 0 (sec)
Interface inside (0.0.0.0): Unknown (Waiting)
Interface outside (0.0.0.0): Unknown (Waiting)
Stateful Failover Logical Update Statistics
Link : Unconfigured.
pixfirewall(config)# .
Detected an Active mate
Beginning configuration replication from mate.
End configuration replication from mate.
pixfirewall(config)# show failover
Failover On
Cable status: N/A - LAN-based failover enabled
Failover unit Secondary
Failover LAN Interface: zwish Ethernet2 (up)
Unit Poll frequency 15 seconds, holdtime 45 seconds
Interface Poll frequency 5 seconds, holdtime 25 seconds
Interface Policy 1
Monitored Interfaces 2 of 250 maximum
Version: Ours 7.2(2), Mate 7.2(2)
Last Failover at: 07:40:21 UTC Apr 24 2020
This host: Secondary - Standby Ready
Active time: 0 (sec)
Interface inside (192.168.1.2): Normal
Interface outside (13.0.1.2): Normal
Other host: Primary - Active
Active time: 90 (sec)
Interface inside (192.168.1.1): Normal
Interface outside (13.0.1.1): Normal
Stateful Failover Logical Update Statistics
Link : Unconfigured.
pixfirewall(config)#
原本是打算用R2 telnet R1的，但发现对比不明显，所以临时在拓扑中加了一个PC（ip为13.0.1.4，为了简单,和不打乱前面的配置，就直接接在了交换机）
2）测试
故障切换前主防火墙和备份防火墙的故障切换配置在上面的命令行中
然后用PC ping R1，设置为50次，然后把主防火墙断电(这里应该还可以使用shutdown关闭接口)
从ping的情况可以看出切换成功了
看一下切换后的PIX2，发现状态为Active，inside和outside的ip是原来主防火墙PIX1，证明试验成功：
标签：pixfirewall,failover,防火墙,PIX,故障,Interface,config,Failover,13.0 来源： https://www.cnblogs.com/zw1sh/p/12771663.html