linux usb驱动记录（一）
作者：互联网
一、linux 下的usb驱动框架
在linux系统中，usb驱动可以从两个角度去观察，一个是主机侧，一个是设备侧。linux usb 驱动的总体框架如下图所示：
从主机侧看usb驱动可分为四层：usb主机控制器硬件底层、usb主机控制器驱动、usb核心和usb设备驱动。
在主机侧要实现的驱动主要分为两类：usb主机控制器驱动和usb设备驱动。主机控制器驱动负责控制插入其中的usb设备，usb设备驱动主要负责usb设备和主机的通信。
usb核心向上为设备驱动提供编程接口，向下为usb控制器驱动提供编程口，维护整个usb设备信息，完成设备热插拔控制，总线数据传输控制。
可以看到这种设备驱动、核心层、主机控制器驱动这种三层结构的驱动框架，与之前分析过linux系统下i2c子系统的驱动架构有异曲同工之处。linux内核中将主机控制器的驱动和外设端的驱动分离，通过一个核心层将某种总线的协议进行抽象，外设端的驱动调用核心层API间接过渡到主机驱动传输函数的调用。
这里借助一张图来对比linux下，i2c、spi、usb三个子系统的相似之处。
这样一对比，就能比较清晰的分析usb主机控制器驱动与usb设备驱动。
二、usb总线驱动程序分析
主机控制器中重要的数据结构：
usb_hcd：描述了USB主机控制器驱动，包含主机控制器的信息
hc_driver：用于操作主机控制器的驱动，该结构体在usb_hcd 中
ohci_hcd： 是usb_hcd 结构体中的私有数据
在主机控制驱动中还是通过平台设备驱动来注册platform_device和platform_driver，然后用平台总线进行匹配，匹配成功之后调用probe函数，在probe函数中做进一步的操作。
probe函数：
static int usb_hcd_s3c2410_probe (const struct hc_driver *driver,
struct platform_device *dev)
{
struct usb_hcd *hcd = NULL;
int retval;
// dev->dev.platform_data == NULL，因此这里不会不用set_power
s3c2410_usb_set_power(dev->dev.platform_data, 1, 1);
s3c2410_usb_set_power(dev->dev.platform_data, 2, 1);
// 创建一个hcd结构体，并做一些设置
hcd = usb_create_hcd(driver, &dev->dev, "s3c24xx");
if (hcd == NULL)
return -ENOMEM;
// 设置内存和IO资源的开始位置
hcd->rsrc_start = dev->resource[0].start;
// 设置内存和IO资源的长度
hcd->rsrc_len = dev->resource[0].end - dev->resource[0].start + 1;
// 申请一块内存资源
if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, hcd_name)) {
dev_err(&dev->dev, "request_mem_region failed\n");
retval = -EBUSY;
goto err_put;
}
// 在clock.c中找到"usb-host"对应的clk结构体
clk = clk_get(&dev->dev, "usb-host");
if (IS_ERR(clk)) {
dev_err(&dev->dev, "cannot get usb-host clock\n");
retval = -ENOENT;
goto err_mem;
}
// 在clock.c中找到"usb-bus-host"对应的clk结构体
usb_clk = clk_get(&dev->dev, "usb-bus-host");
if (IS_ERR(usb_clk)) {
dev_err(&dev->dev, "cannot get usb-bus-host clock\n");
retval = -ENOENT;
goto err_clk;
}
// 使能时钟 使能过流检查
s3c2410_start_hc(dev, hcd);
// io端口重映射
hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len);
if (!hcd->regs) {
dev_err(&dev->dev, "ioremap failed\n");
retval = -ENOMEM;
goto err_ioremap;
}
// 初始化ohci_hcd 结构体ohci->next_statechange = jiffies
ohci_hcd_init(hcd_to_ohci(hcd));
// 这个函数下边分析 一个usb主机控制器对应一个usb_hcd，对应一条usb总线，集成一个root_hub
retval = usb_add_hcd(hcd, dev->resource[1].start, IRQF_DISABLED);
if (retval != 0)
goto err_ioremap;
return 0;
err_ioremap:
s3c2410_stop_hc(dev);
iounmap(hcd->regs);
clk_put(usb_clk);
err_clk:
clk_put(clk);
err_mem:
release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
err_put:
usb_put_hcd(hcd);
return retval;
}
在probe函数中主要的任务如下：
（1）创建一个usb_hcd结构体===>和i2c控制器驱动中的中分配一个i2c_adapter一样
（2）设置这个这个usb_hcd结构体（设置操作主机控制器的hc_driver）===>设置i2c_adapter结构体（设置操作i2c_adapter的transfer函数）
（3）从platform_device中获取到硬件资源，进行内存映射
（4）使能时钟
（5）usb_add_hcd
usb_create_hcd函数：
struct usb_hcd *usb_create_hcd (const struct hc_driver *driver,
struct device *dev, const char *bus_name)
{
struct usb_hcd *hcd;
hcd = kzalloc(sizeof(*hcd) + driver->hcd_priv_size, GFP_KERNEL);
dev_set_drvdata(dev, hcd);
...
// 初始化hcd下边的usb_bus，为后边将其加入到usb_bus 中做准备：
//bus->devnum_next = 1; bus->root_hub = NULL; bus->busnum = -1;
//bus->bandwidth_allocated = 0; bus->bandwidth_int_reqs = 0;
//bus->bandwidth_isoc_reqs = 0;
usb_bus_init(&hcd->self);
hcd->self.controller = dev;
hcd->self.bus_name = bus_name;
hcd->self.uses_dma = (dev->dma_mask != NULL);
// 初始定时器用来轮询控制器的root_hub的状态改变
init_timer(&hcd->rh_timer);
// 注册定时器中断服务函数
hcd->rh_timer.function = rh_timer_func;
hcd->rh_timer.data = (unsigned long) hcd;
#ifdef CONFIG_USB_SUSPEND
INIT_WORK(&hcd->wakeup_work, hcd_resume_work);
#endif
mutex_init(&hcd->bandwidth_mutex);
// 给hcd添加主机控制器驱动函数 driver==ohci_s3c2410_hc_driver
hcd->driver = driver;
hcd->product_desc = (driver->product_desc) ? driver->product_desc :
"USB Host Controller";
return hcd;
}
usb_add_hcd函数：一个usb主机控制器对应一条usb总线，集成一个root_hub，对应一个usb_hcd。
int usb_add_hcd(struct usb_hcd *hcd,
unsigned int irqnum, unsigned long irqflags)
{
// 初始化缓存池
if ((retval = hcd_buffer_create(hcd)) != 0) {
dev_dbg(hcd->self.controller, "pool alloc failed\n");
return retval;
}
//设置hcd下usb_bus的busnum并将其挂到usb_bus_list这个链表中 hcd->self 在usb_create_hcd 中已经初始化了 (注册完之后hcd->self.busnum = 1)
if ((retval = usb_register_bus(&hcd->self)) < 0)
goto err_register_bus;
// 创建一个root_hub
if ((rhdev = usb_alloc_dev(NULL, &hcd->self, 0)) == NULL) {
dev_err(hcd->self.controller, "unable to allocate root hub\n");
retval = -ENOMEM;
goto err_allocate_root_hub;
}
// 将上边分配好的usb_device挂在主机控制的usb_bus下
hcd->self.root_hub = rhdev;
// 根据ohci_s3c2410_hc_driver(HCD_USB11 | HCD_MEMORY,)下的flag 选择 root_hub 的speed
switch (hcd->driver->flags & HCD_MASK) {
case HCD_USB11:
rhdev->speed = USB_SPEED_FULL;
break;
case HCD_USB2:
rhdev->speed = USB_SPEED_HIGH;
break;
case HCD_USB3:
rhdev->speed = USB_SPEED_SUPER;
break;
default:
goto err_set_rh_speed;
}
device_init_wakeup(&rhdev->dev, 1);
if (hcd->driver->reset && (retval = hcd->driver->reset(hcd)) < 0) {
dev_err(hcd->self.controller, "can't setup\n");
goto err_hcd_driver_setup;
}
hcd->rh_pollable = 1;
/* NOTE: root hub and controller capabilities may not be the same */
if (device_can_wakeup(hcd->self.controller)
&& device_can_wakeup(&hcd->self.root_hub->dev))
dev_dbg(hcd->self.controller, "supports USB remote wakeup\n");
/* enable irqs just before we start the controller */
// 接下来使能中断
// 接下来执行主机控制器的启动函数
/* starting here, usbcore will pay attention to this root hub */
rhdev->bus_mA = min(500u, hcd->power_budget);
if ((retval = register_root_hub(hcd)) != 0)
goto err_register_root_hub;
retval = sysfs_create_group(&rhdev->dev.kobj, &usb_bus_attr_group);
if (retval < 0) {
printk(KERN_ERR "Cannot register USB bus sysfs attributes: %d\n",
retval);
goto error_create_attr_group;
}
if (hcd->uses_new_polling && HCD_POLL_RH(hcd))
usb_hcd_poll_rh_status(hcd);
return retval;
...
}
在usb_add_hcd中，最主要干的一件事是创建一个root_hub，这个root_hub的数据类型是一个usb_device，并将这个root_hub注册到usb总线中。
这里大概解释一下什么是root_hub。在我们的电脑上通常有几个usb端口，这些端口可以用来连接一个普通的usb设备，或者一个hub，hub是一个usb设备，可以用来扩展连接usb设备的端口数量。通常情况下主机控制器的物理端口由一个虚拟的root_hub来管理。这个hub是主机控制器的设备驱动虚拟的，用来统一管理总线拓扑。用一张图说明usb系统的拓扑结构。
register_root_hub函数的调用太复杂了，这里先抽象出其函数调用过程如下：
为了分析清楚root_hub下的dev到底与总线上的哪一个device_driver匹配需要分析usb总线上的match函数
static int usb_device_match(struct device *dev, struct device_driver *drv)
{
// 需要匹配的是usb_device时的情况
if (is_usb_device(dev)) {
/* interface drivers never match devices */
if (!is_usb_device_driver(drv))
return 0;
/* TODO: Add real matching code */
return 1;
}
// 需要匹配的是接口的情况
else if (is_usb_interface(dev)) {
struct usb_interface *intf;
struct usb_driver *usb_drv;
const struct usb_device_id *id;
/* device drivers never match interfaces */
if (is_usb_device_driver(drv))
return 0;
intf = to_usb_interface(dev);
usb_drv = to_usb_driver(drv);
id = usb_match_id(intf, usb_drv->id_table);
if (id)
return 1;
id = usb_match_dynamic_id(intf, usb_drv);
if (id)
return 1;
}
return 0;
}
对于传入的match函数的dev其dev->type是usb_device_type（在分配usb_alloc_dev中已经设置了）。
现在看usb总线上有哪些device_driver：在/core/usb.c中我们可以看到已经注册了两个usb_driver结构体 usbfs_driver和hub_driver
一个usb_device_driver结构体 usb_generic_driver
（这里跳转的比较突然，这三个结构体的注册是在usb_init函数中进行的）
所以match函数中传入的dev会和这三个已经注册到usb_bus上的device_driver进行匹配，这里看哪一个usb_driver下的device_driver会匹配成功，也就是看usbdrv_wrap->for_devices的值，这个值需要在usb_register函数中查看，这里给出结果。其实从driver的名字就可以看出只有usb_device_driver （usb设备驱动）是能够和device（设备）进行匹配的。
因此root_hub->dev会和usb_generic_driver->drvwrap.driver进行匹配，匹配完成之后会执行probe函数。那么这个probe函数有是哪一个呢？probe函数肯定是usb_generic_driver->drvwrap.driver.probe
这个函数在usb_register_device_driver(&usb_generic_driver, THIS_MODULE)中进行了设置usb_generic_driver->drvwrap.driver.probe = usb_probe_device
usb_probe_device函数的分析：
static int usb_probe_device(struct device *dev)
{
// 这里通过container_of 找到usb_device_driver 和 usb_device
// 注意在really_probe 函数中已经将dev->driver 挂上了 device_driver ，所以这个地方才能找到usb_device_driver
struct usb_device_driver *udriver = to_usb_device_driver(dev->driver);
struct usb_device *udev = to_usb_device(dev);
int error = 0;
dev_dbg(dev, "%s\n", __func__);
/* TODO: Add real matching code */
/* The device should always appear to be in use
* unless the driver suports autosuspend.
*/
if (!udriver->supports_autosuspend)
error = usb_autoresume_device(udev);
// 程序执行到这里可以看到饶了一大圈的probe函数就是usb_generic_driver->probe函数 也就是generic_probe 函数
if (!error)
error = udriver->probe(udev);
return error;
}
因此接下分析generic_probe 函数：
static int generic_probe(struct usb_device *udev)
{
int err, c;
if (usb_device_is_owned(udev))
; /* Don't configure if the device is owned */
// 在创建root_hub 时分配usb_device时已经设置了dev->authorized = 1
else if (udev->authorized == 0)
dev_err(&udev->dev, "Device is not authorized for usage\n");
else {
// 因此会执行到这里来配置操作
c = usb_choose_configuration(udev);
if (c >= 0) {
err = usb_set_configuration(udev, c);
if (err) {
dev_err(&udev->dev, "can't set config #%d, error %d\n",
c, err);
}
}
}
/* USB device state == configured ... usable */
usb_notify_add_device(udev);
return 0;
}
在这里我们可以看一下到底对着root->hub选择了什么配置，设置了什么配置
int usb_choose_configuration(struct usb_device *udev)
{
int i;
int num_configs;
int insufficient_power = 0;
struct usb_host_config *c, *best;
best = NULL;
// root_hub下的一些与配置有关的东西在usb_new_device中都读取出来然后放到了root_hub下的config中
c = udev->config;
// 有多少项配置
num_configs = udev->descriptor.bNumConfigurations;
// 遍历所有的配置项
for (i = 0; i < num_configs; (i++, c++)) {
struct usb_interface_descriptor *desc = NULL;
/* It's possible that a config has no interfaces! */
// 有可能一个配置没有接口，所以要做判断
if (c->desc.bNumInterfaces > 0)
// 取出配置下的第一个接口
desc = &c->intf_cache[0]->altsetting->desc;
/*
* HP's USB bus-powered keyboard has only one configuration
* and it claims to be self-powered; other devices may have
* similar errors in their descriptors. If the next test
* were allowed to execute, such configurations would always
* be rejected and the devices would not work as expected.
* In the meantime, we run the risk of selecting a config
* that requires external power at a time when that power
* isn't available. It seems to be the lesser of two evils.
*
* Bugzilla #6448 reports a device that appears to crash
* when it receives a GET_DEVICE_STATUS request! We don't
* have any other way to tell whether a device is self-powered,
* but since we don't use that information anywhere but here,
* the call has been removed.
*
* Maybe the GET_DEVICE_STATUS call and the test below can
* be reinstated when device firmwares become more reliable.
* Don't hold your breath.
*/
#if 0
/* Rule out self-powered configs for a bus-powered device */
if (bus_powered && (c->desc.bmAttributes &
USB_CONFIG_ATT_SELFPOWER))
continue;
#endif
/*
* The next test may not be as effective as it should be.
* Some hubs have errors in their descriptor, claiming
* to be self-powered when they are really bus-powered.
* We will overestimate the amount of current such hubs
* make available for each port.
*
* This is a fairly benign sort of failure. It won't
* cause us to reject configurations that we should have
* accepted.
*/
/* Rule out configs that draw too much bus current */
if (c->desc.bMaxPower * 2 > udev->bus_mA) {
insufficient_power++;
continue;
}
/* When the first config's first interface is one of Microsoft's
* pet nonstandard Ethernet-over-USB protocols, ignore it unless
* this kernel has enabled the necessary host side driver.
* But: Don't ignore it if it's the only config.
*/
if (i == 0 && num_configs > 1 && desc &&
(is_rndis(desc) || is_activesync(desc))) {
#if !defined(CONFIG_USB_NET_RNDIS_HOST) && !defined(CONFIG_USB_NET_RNDIS_HOST_MODULE)
continue;
#else
best = c;
#endif
}
/* From the remaining configs, choose the first one whose
* first interface is for a non-vendor-specific class.
* Reason: Linux is more likely to have a class driver
* than a vendor-specific driver. */
else if (udev->descriptor.bDeviceClass !=
USB_CLASS_VENDOR_SPEC &&
(desc && desc->bInterfaceClass !=
USB_CLASS_VENDOR_SPEC)) {
best = c;
break;
}
/* If all the remaining configs are vendor-specific,
* choose the first one. */
else if (!best)
best = c;
}
if (insufficient_power > 0)
dev_info(&udev->dev, "rejected %d configuration%s "
"due to insufficient available bus power\n",
insufficient_power, plural(insufficient_power));
if (best) {
i = best->desc.bConfigurationValue;
dev_dbg(&udev->dev,
"configuration #%d chosen from %d choice%s\n",
i, num_configs, plural(num_configs));
} else {
i = -1;
dev_warn(&udev->dev,
"no configuration chosen from %d choice%s\n",
num_configs, plural(num_configs));
}
return i; // 这里返回了一个系统觉得合适的配置项的编号
}
返回的这个最好的配置项的编号传入到usb_set_configuration，猜测要对此项配置进行设置。
int usb_set_configuration(struct usb_device *dev, int configuration)
{
int i, ret;
struct usb_host_config *cp = NULL;
struct usb_interface **new_interfaces = NULL;
struct usb_hcd *hcd = bus_to_hcd(dev->bus);
int n, nintf;
// 首先根据选择的配置项的编号 找到相应的配置
if (dev->authorized == 0 || configuration == -1)
configuration = 0;
else {
for (i = 0; i < dev->descriptor.bNumConfigurations; i++) {
if (dev->config[i].desc.bConfigurationValue ==
configuration) {
cp = &dev->config[i];
break;
}
}
}
if ((!cp && configuration != 0))
return -EINVAL;
/* The USB spec says configuration 0 means unconfigured.
* But if a device includes a configuration numbered 0,
* we will accept it as a correctly configured state.
* Use -1 if you really want to unconfigure the device.
*/
//当configuration==0 时发出警告，0是无效的配置，但仍然认为他是正确的
if (cp && configuration == 0)
dev_warn(&dev->dev, "config 0 descriptor??\n");
/* Allocate memory for new interfaces before doing anything else,
* so that if we run out then nothing will have changed. */
n = nintf = 0;
// 得到接口总数，并分配内存
if (cp) {
nintf = cp->desc.bNumInterfaces;
new_interfaces = kmalloc(nintf * sizeof(*new_interfaces),
GFP_NOIO);
if (!new_interfaces) {
dev_err(&dev->dev, "Out of memory\n");
return -ENOMEM;
}
for (; n < nintf; ++n) {
new_interfaces[n] = kzalloc(
sizeof(struct usb_interface),
GFP_NOIO);
if (!new_interfaces[n]) {
dev_err(&dev->dev, "Out of memory\n");
ret = -ENOMEM;
free_interfaces:
while (--n >= 0)
kfree(new_interfaces[n]);
kfree(new_interfaces);
return ret;
}
}
i = dev->bus_mA - cp->desc.bMaxPower * 2;
if (i < 0)
dev_warn(&dev->dev, "new config #%d exceeds power "
"limit by %dmA\n",
configuration, -i);
}
/* Wake up the device so we can send it the Set-Config request */
// 配置前唤醒设备
ret = usb_autoresume_device(dev);
if (ret)
goto free_interfaces;
/* if it's already configured, clear out old state first.
* getting rid of old interfaces means unbinding their drivers.
*/
if (dev->state != USB_STATE_ADDRESS)
usb_disable_device(dev, 1); /* Skip ep0 */
/* Get rid of pending async Set-Config requests for this device */
cancel_async_set_config(dev);
/* Make sure we have bandwidth (and available HCD resources) for this
* configuration. Remove endpoints from the schedule if we're dropping
* this configuration to set configuration 0. After this point, the
* host controller will not allow submissions to dropped endpoints. If
* this call fails, the device state is unchanged.
*/
mutex_lock(&hcd->bandwidth_mutex);
ret = usb_hcd_alloc_bandwidth(dev, cp, NULL, NULL);
if (ret < 0) {
mutex_unlock(&hcd->bandwidth_mutex);
usb_autosuspend_device(dev);
goto free_interfaces;
}
// 设置配置
ret = usb_control_msg(dev, usb_sndctrlpipe(dev, 0),
USB_REQ_SET_CONFIGURATION, 0, configuration, 0,
NULL, 0, USB_CTRL_SET_TIMEOUT);
if (ret < 0) {
/* All the old state is gone, so what else can we do?
* The device is probably useless now anyway.
*/
cp = NULL;
}
dev->actconfig = cp;
if (!cp) {
usb_set_device_state(dev, USB_STATE_ADDRESS);
usb_hcd_alloc_bandwidth(dev, NULL, NULL, NULL);
mutex_unlock(&hcd->bandwidth_mutex);
usb_autosuspend_device(dev);
goto free_interfaces;
}
mutex_unlock(&hcd->bandwidth_mutex);
usb_set_device_state(dev, USB_STATE_CONFIGURED);
/* Initialize the new interface structures and the
* hc/hcd/usbcore interface/endpoint state.
*/
// 接下来设置这个配置的接口并将接口注册到usb总线下
for (i = 0; i < nintf; ++i) {
struct usb_interface_cache *intfc;
struct usb_interface *intf;
struct usb_host_interface *alt;
cp->interface[i] = intf = new_interfaces[i];
intfc = cp->intf_cache[i];
intf->altsetting = intfc->altsetting;
intf->num_altsetting = intfc->num_altsetting;
intf->intf_assoc = find_iad(dev, cp, i);
kref_get(&intfc->ref);
alt = usb_altnum_to_altsetting(intf, 0);
/* No altsetting 0? We'll assume the first altsetting.
* We could use a GetInterface call, but if a device is
* so non-compliant that it doesn't have altsetting 0
* then I wouldn't trust its reply anyway.
*/
if (!alt)
alt = &intf->altsetting[0];
intf->cur_altsetting = alt;
usb_enable_interface(dev, intf, true);
intf->dev.parent = &dev->dev;
intf->dev.driver = NULL;
intf->dev.bus = &usb_bus_type;
intf->dev.type = &usb_if_device_type;
intf->dev.groups = usb_interface_groups;
intf->dev.dma_mask = dev->dev.dma_mask;
INIT_WORK(&intf->reset_ws, __usb_queue_reset_device);
intf->minor = -1;
device_initialize(&intf->dev);
pm_runtime_no_callbacks(&intf->dev);
dev_set_name(&intf->dev, "%d-%s:%d.%d",
dev->bus->busnum, dev->devpath,
configuration, alt->desc.bInterfaceNumber);
}
kfree(new_interfaces);
if (cp->string == NULL &&
!(dev->quirks & USB_QUIRK_CONFIG_INTF_STRINGS))
cp->string = usb_cache_string(dev, cp->desc.iConfiguration);
/* Now that all the interfaces are set up, register them
* to trigger binding of drivers to interfaces. probe()
* routines may install different altsettings and may
* claim() any interfaces not yet bound. Many class drivers
* need that: CDC, audio, video, etc.
*/
for (i = 0; i < nintf; ++i) {
struct usb_interface *intf = cp->interface[i];
dev_dbg(&dev->dev,
"adding %s (config #%d, interface %d)\n",
dev_name(&intf->dev), configuration,
intf->cur_altsetting->desc.bInterfaceNumber);
device_enable_async_suspend(&intf->dev);
ret = device_add(&intf->dev);
if (ret != 0) {
dev_err(&dev->dev, "device_add(%s) --> %d\n",
dev_name(&intf->dev), ret);
continue;
}
create_intf_ep_devs(intf);
}
usb_autosuspend_device(dev);
return 0;
}
简单看完usb_set_configuration之后，看一下此刻在/sys/bus/usb/device 路径存在的设备如下：
usb1这个设备是在之前一次register_root_hub中的device_add中添加的，而1-0:1.0是在sub_set_configuration中device_add添加的，对应表示 总线号-设备路径：配置号-接口号
1-0:1.0表示usb控制器1下的usb_hub下的1号配置的0号接口
注意到这里有出现了device_add，这又是一长串的函数调用，但是还是向总线注册设备、与总线上的device_driver进行匹配，匹配成功之后执行probe函数。所以在这里又得分析usb_device_match函数和probe，重点是这个probe函数执行的是哪一个函数？
之前分析过usb_device_match函数，这次传入到usb_device_match中的dev是一个接口类型的，所以应该执行usb_device_match中的第二条分支，通过id来进行匹配。这次与root_hub下的接口匹配的应该是hub_driver->drvwrap.driver，通过静态id_table的匹配成功之后应该执行usb_probe_interface这个函数。
static int usb_probe_interface(struct device *dev)
{
struct usb_driver *driver = to_usb_driver(dev->driver);
struct usb_interface *intf = to_usb_interface(dev);
struct usb_device *udev = interface_to_usbdev(intf);
const struct usb_device_id *id;
....
// 执行到这里又回到了hub_driver下的hub_probe函数
// 可以看到这里的probe函数的调用是一层套一层的，但最终都会执行到driver下的probe函数
error = driver->probe(intf, id);
if (error)
goto err;
....
}
hub_probe函数：
static int hub_probe(struct usb_interface *intf, const struct usb_device_id *id)
{
struct usb_host_interface *desc;
struct usb_endpoint_descriptor *endpoint;
struct usb_device *hdev;
struct usb_hub *hub;
desc = intf->cur_altsetting;
hdev = interface_to_usbdev(intf);
/* Hubs have proper suspend/resume support */
usb_enable_autosuspend(hdev);
if (hdev->level == MAX_TOPO_LEVEL) {
dev_err(&intf->dev,
"Unsupported bus topology: hub nested too deep\n");
return -E2BIG;
}
#ifdef CONFIG_USB_OTG_BLACKLIST_HUB
if (hdev->parent) {
dev_warn(&intf->dev, "ignoring external hub\n");
return -ENODEV;
}
#endif
/* Some hubs have a subclass of 1, which AFAICT according to the */
/* specs is not defined, but it works */
if ((desc->desc.bInterfaceSubClass != 0) &&
(desc->desc.bInterfaceSubClass != 1)) {
descriptor_error:
dev_err (&intf->dev, "bad descriptor, ignoring hub\n");
return -EIO;
}
//hub interface的endpoint数目为1,这里的数目没有包括ep0
if (desc->desc.bNumEndpoints != 1)
goto descriptor_error;
//获取端点描述符
endpoint = &desc->endpoint[0].desc;
//判断端点是不是in方向的端点，
if (!usb_endpoint_is_int_in(endpoint))
goto descriptor_error;
/* We found a hub */
dev_info (&intf->dev, "USB hub found\n");
// 分配一个usb_hub
hub = kzalloc(sizeof(*hub), GFP_KERNEL);
if (!hub) {
dev_dbg (&intf->dev, "couldn't kmalloc hub struct\n");
return -ENOMEM;
}
//初始化引用计数
kref_init(&hub->kref);
INIT_LIST_HEAD(&hub->event_list);
hub->intfdev = &intf->dev;
hub->hdev = hdev;
INIT_DELAYED_WORK(&hub->leds, led_work);
INIT_DELAYED_WORK(&hub->init_work, NULL);
usb_get_intf(intf);
usb_set_intfdata (intf, hub);
intf->needs_remote_wakeup = 1;
if (hdev->speed == USB_SPEED_HIGH)
highspeed_hubs++;
// 配置hub
if (hub_configure(hub, endpoint) >= 0)
return 0;
hub_disconnect (intf);
return -ENODEV;
}
程序接下来的执行过程以及框架的分析过程在下一篇博客中分析
标签：usb,hub,driver,dev,hcd,linux,device,驱动 来源： https://www.cnblogs.com/zf1-2/p/10887193.html