其他分享
首页 > 其他分享> > man 5 interfaces @20210329

man 5 interfaces @20210329

作者:互联网

DESCRIPTION

/etc/network/interfaces contains network interface configuration information for the ifup(8) and
ifdown(8) commands. This is where you configure how your system is connected to the network.

EXAMPLE

The following example configures two network interfaces: eth0 is brought up at boot, and uses DHCP
for IPv4 and SLAAC for IPv6, whereas eth1 is brought up whenever the network hardware is detected,
and is configured with static IPv4 and IPv6 addresses.

auto eth0
allow-hotplug eth1

iface eth0 inet dhcp

iface eth0 inet6 auto

iface eth1 inet static

address 192.168.1.2/24
gateway 192.168.1.1

 

iface eth1 inet6 static

address fec0:0:0:1::2/64
gateway fec0:0:0:1::1

 

FILE FORMAT

Lines starting with `#' are ignored. Note that end-of-line comments are NOT supported, comments must
be on a line of their own.

A line may be extended across multiple lines by making the last character a backslash.

The file consists of zero or more "iface", "mapping", "auto", "allow-", "rename", "source" and
"source-directory" stanzas. These will be described in more detail in the following sections.

INTERFACE SELECTION

Lines beginning with the word "auto" are used to identify the physical interfaces to be brought up
when ifup is run with the -a option. (This option is also used by the system boot scripts, so
interfaces marked "auto" are brought up at boot time.) Physical interface names should follow the
word "auto" on the same line. There can be multiple "auto" stanzas. ifup brings the named inter‐
faces up in the order listed.

Lines beginning with "allow-" are used to identify interfaces that should be brought up automati‐
cally by various subsytems. This may be done using a command such as "ifup --allow=hotplug eth0
eth1", which will only bring up eth0 or eth1 if it is listed in an "allow-hotplug" line. Note that
"allow-auto" and "auto" are synonyms. (Interfaces marked "allow-hotplug" are brought up when udev
detects them. This can either be during boot if the interface is already present, or at a later
time, for example when plugging in a USB network card. Please note that this does not have anything
to do with detecting a network cable being plugged in.)

Lines beginning with "no-auto-down" are used to identify interfaces that should not be brought down
by the command "ifdown -a". Its main use is to prevent an interface from being brought down during
system shutdown time, for example if the root filesystem is a network filesystem and the interface
should stay up until the very end. Note that you can still bring down the interface by specifying
the interface name explicitly.

Lines beginning with "no-scripts" are used to identify interfaces for which scripts in /etc/net‐
work/if-*.d/ should not be run when those interfaces are brought up or down. he above will match
eth0 and eth1, and will bring up both interfaces using the "iface eth" stanza.

INTERFACE RENAMING

Lines beginning with "rename" are used to rename interfaces. It takes one or more arguments in the
form of "CUR=NEW", where CUR is the name of an existing interface, and NEW is the new name. This
becomes very powerful when combined with pattern matching for the CUR interface.

Interfaces are renamed whenever "ifup" is called. Renaming logically happens before anything else
is done. So if an interface is started with the name "foo", and it has to be renamed to "bar" and
brought up at boot time, then one should use the following /etc/network/interfaces file:

rename foo=bar
auto bar
iface bar ...

However, if the interface is not renamed yet, it is possible to use both "ifup foo" and "ifup bar".
The former command will then automatically be converted to the latter. This is mainly useful when
ifup is called automatically whenever an interface is hotplugged.

Interface renaming only works if the operating system supports it, if an interface is not renamed to
another existing interface, and may require that the interface that is to be renamed has not been
brought up yet. If ifup tries to rename an interface and it fails, it will exit with an error.

INCLUDING OTHER FILES

Lines beginning with "source" are used to include stanzas from other files, so configuration can be
split into many files. The word "source" is followed by the path of file to be sourced. Shell wild‐
cards can be used. (See wordexp(3) for details.)

Similarly, "source-directory" keyword is used to source multiple files at once, without specifying
them individually or using shell globs. Additionally, when "source-directory" is used, names of the
files are checked to match the following regular expression: ^[a-zA-Z0-9_-]+$. In other words, the
names must consist entirely of ASCII upper- and lower-case letters, ASCII digits, ASCII underscores,
and ASCII minus-hyphens. In the directory path, shell wildcards may be used as well.

When sourcing files or directories, if a path doesn't have a leading slash, it's considered relative
to the directory containing the file in which the keyword is placed. In the example above, if the
file is located at /etc/network/interfaces, paths to the included files are understood to be under
/etc/network.

By default, on a freshly installed Debian system, the interfaces file includes a line to source
files in the /etc/network/interfaces.d directory.

MAPPINGS

Stanzas beginning with the word "mapping" are used to determine how a logical interface name is cho‐
sen for a physical interface that is to be brought up. The first line of a mapping stanza consists
of the word "mapping" followed by a pattern in shell glob syntax. Each mapping stanza must contain
a script definition. The named script is run with the physical interface name as its argument and
with the contents of all following "map" lines (without the leading "map") in the stanza provided to
it on its standard input. The script must print a string on its standard output before exiting. See
/usr/share/doc/ifupdown/examples for examples of what the script must print.

Mapping a name consists of searching the remaining mapping patterns and running the script corre‐
sponding to the first match; the script outputs the name to which the original is mapped.

ifup is normally given a physical interface name as its first non-option argument. ifup also uses
this name as the initial logical name for the interface unless it is accompanied by a suffix of the
form =LOGICAL, in which case ifup chooses LOGICAL as the initial logical name for the interface. It
then maps this name, possibly more than once according to successive mapping specifications, until
no further mappings are possible. If the resulting name is the name of some defined logical inter‐
face then ifup attempts to bring up the physical interface as that logical interface. Otherwise
ifup exits with an error.

INTERFACE DEFINITIONS

Stanzas defining logical interfaces start with a line consisting of the word "iface" followed by the
name of the logical interface. In simple configurations without mapping stanzas this name should
simply be the name of the physical interface to which it is to be applied. (The default mapping
script is, in effect, the echo command.) The interface name is followed by the name of the address
family that the interface uses. This will be "inet" for TCP/IP networking, but there is also some
support for IPX networking ("ipx"), and IPv6 networking ("inet6"). Following that is the name of
the method used to configure the interface.

Additional options can be given on subsequent lines in the stanza. Which options are available
depends on the family and method, as described below. Additional options can be made available by
other Debian packages. For example, the wireless-tools package makes available a number of options
prefixed with "wireless-" which can be used to configure the interface using iwconfig(8). (See
wireless(7) for details.) A list of packages providing additional options is mentioned in the sec‐
tion "OPTIONS PROVIDED BY OTHER PACKAGE".

Options are usually indented for clarity (as in the example above) but are not required to be.

Multiple "iface" stanzas can be given for the same interface, in which case all of the configured
addresses and options for that interface will be applied when bringing up that interface. This is
useful to configure both IPv4 and IPv6 addresses on the same interface (although if no inet6 stanza
is present, the kernel will normally still perform stateless address autoconfiguration if there is
an IPv6 route advertisement daemon on the network). It can also be used to configure multiple
addresses of the same type on a single interface.

INTERFACE TEMPLATES

It is possible to define interface definition templates and extend them using the inherits keyword:

iface ethernet inet static

mtu 1500
hwaddress 11:22:33:44:55:66

 

iface eth0 inet static inherits ethernet

address 192.168.1.2/24

 

This may be useful to separate link-level settings shared by multiple interfaces from, for example,
IP address settings specific to every interface.

PATTERN MATCHING INTERFACES

It is possible to use patterns to match one or more real interfaces. These patterns can currently
appear in lines beginning with "auto", "allow-", "rename" and on the command line. A pattern has
the following format (see below for exceptions for GNU/Hurd):

[VARIABLE]/VALUE[/[OPTIONS]][=LOGICAL]

If no VARIABLE is given, this pattern will match interface names against the given VALUE. VALUE can
contain wildcard patterns such as ? and *, see the fnmatch(3) function. When ifup or ifdown is run,
patterns are replaces by all real interfaces that are currently known to the operating system kernel
and whose names match the pattern. For example, given the following line:

auto /eth*

If the kernel knows about the interfaces with names lo, eth0 and eth1, then the above line is then
interpreted as:

auto eth0 eth1

Note that there must still be valid "iface" stanzas for each matching interface. However, it is
possible to combine a pattern with a mapping to a logical interface, like so:

auto /eth*=eth
iface eth inet dhcp

Valid variable names are "mac", in which case value is matched against the interface's MAC address.
On Linux, the variable name can also be any filename in /sys/class/net/<iface>/, in which case the
value is matched against the contents of the corresponding file.

The OPTIONS field currently only supports a number. If given, only the n-th interface that has a
matching value will actually be used, where n is the number given, starting at 1. So /eth*/1 will
match the first interface whose name starts with eth.

On GNU/Hurd, interface names start with /dev/, and this obviously clashes with the format for pat‐
terns. To ensure an interface name like /dev/eth0 does not get interpreted as a pattern, any pat‐
tern that starts with /dev/ is ignored, and instead interpreted as a literal interface name. To
make a pattern that matches interface names on GNU/Hurd, use something like:

auto /?dev?eth*=eth
iface eth inet dhcp

VLAN INTERFACES

To ease the configuration of VLAN interfaces, interfaces having . (full stop character) in the name
are configured as 802.1q tagged virtual LAN interface. For example, interface eth0.1 is a virtual
interface having eth0 as physical link, with VLAN ID 1.

IFACE OPTIONS

The following "command" options are available for every family and method. Each of these options
can be given multiple times in a single stanza, in which case the commands are executed in the order
in which they appear in the stanza. (You can ensure a command never fails by suffixing them with
"|| true".)

pre-up command

Run command before bringing the interface up. If this command fails then ifup aborts,
refraining from marking the interface as configured, prints an error message, and exits with
status 0. This behavior may change in the future.

 

up command

post-up command

Run command after bringing the interface up. If this command fails then ifup aborts,
refraining from marking the interface as configured (even though it has really been config‐
ured), prints an error message, and exits with status 0. This behavior may change in the
future.

 

down command

pre-down command

Run command before taking the interface down. If this command fails then ifdown aborts,
marks the interface as deconfigured (even though it has not really been deconfigured), and
exits with status 0. This behavior may change in the future.

 

post-down command

Run command after taking the interface down. If this command fails then ifdown aborts, marks
the interface as deconfigured, and exits with status 0. This behavior may change in the
future.

 

description name

Alias interface by name

 

There exists for each of the above mentioned options a directory /etc/network/if-<option>.d/ the
scripts in which are run (with no arguments) using run-parts(8) after the option itself has been
processed. Please note that as post-up and pre-down are aliases, no files in the corresponding
directories are processed. Please use if-up.d and if-down.d directories instead.

All of these commands have access to the following environment variables.

IFACE The physical name of the interface being processed, or "--all" (see below).

LOGICAL

The logical name of the interface being processed, or "auto" (see below).

 

ADDRFAM

The address family of the interface, or "meta" (see below).

 

METHOD The method of the interface (e.g., static), or "none" (see below).

CLASS The class of interfaces being processed. This is a copy of the value given to the --allow

option when running ifup or ifdown, otherwise it is set to "auto" when the --all option is
used.

 

MODE start if run from ifup, stop if run from ifdown.

PHASE As per MODE, but with finer granularity, distinguishing the pre-up, post-up, pre-down and

post-down phases.

 

VERBOSITY

Indicates whether --verbose was used; set to 1 if so, 0 if not.

 

PATH The command search path: /usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin

Additionally, all options given in an interface definition stanza are exported to the environment in
upper case with "IF_" prepended and with hyphens converted to underscores and non-alphanumeric char‐
acters discarded.

When ifupdown is being called with the --all option, before doing anything to interfaces, if calls
all the hook scripts (pre-up or down) with IFACE set to "--all", LOGICAL set to the current value of
--allow parameter (or "auto" if it's not set), ADDRFAM="meta" and METHOD="none". After all the
interfaces have been brought up or taken down, the appropriate scripts (up or post-down) are exe‐
cuted.

OPTIONS PROVIDED BY OTHER PACKAGES

This manual page documents the configuration options provided by the ifupdown package. However,
other packages can make other options available for use in /etc/network/interfaces. Here is a list
of packages that provide such extensions:

arping, avahi-autoipd, avahi-daemon, bind9, bridge-utils, clamav-freshclam, controlaula, epoptes-
client, ethtool, guidedog, hostap-utils, hostapd, htpdate, ifenslave, ifmetric, ifupdown-extra,
ifupdown-multi, ifupdown-scripts-zg2, initscripts, isatapd, linux-wlan-ng, lprng, macchanger,
miredo, nslcd, ntpdate, openntpd, openresolv, openssh-server, openvpn, openvswitch-switch, postfix,
resolvconf, sendmail-base, shorewall-init, slrn, slrnpull, tinc, ucarp, uml-utilities, uruk, vde2,
vlan, vzctl, whereami, wide-dhcpv6-client, wireless-tools, wpasupplicant.

Please consult the documentation of those packages for information about how they extend ifupdown.

INET ADDRESS FAMILY

This section documents the methods available in the inet address family.

The loopback Method

This method may be used to define the IPv4 loopback interface.

Options

		(No options)

The static Method

This method may be used to define Ethernet interfaces with statically allocated IPv4 addresses.

Options

		address address
				Address (dotted quad/netmask) required
		netmask mask
				Netmask (dotted quad or CIDR)
		broadcast broadcast_address
				Broadcast address (dotted quad, + or -). Default value: "+"
		metric metric
				Routing metric for default gateway (integer)
		gateway address
				Default gateway (dotted quad)
		pointopoint address
				Address of other end point (dotted quad). Note the spelling of "point-to".
		hwaddress address
				Link local address or "random".
		mtu size
				MTU size
		scope  Address validity scope. Possible values: global, link, host

The manual Method

This method may be used to define interfaces for which no configuration is done by default. Such
interfaces can be configured manually by means of up and down commands or /etc/network/if-*.d
scripts.

Options

		hwaddress address
				Link local address or "random".
		mtu size
				MTU size

The dhcp Method

This method may be used to obtain an address via DHCP with any of the tools: dhclient, pump, udhcpc,
dhcpcd. (They have been listed in their order of precedence.) If you have a complicated DHCP setup
you should note that some of these clients use their own configuration files and do not obtain their
configuration information via ifup.

Options

		hostname hostname
				Hostname to be requested (pump, dhcpcd, udhcpc)
		metric metric
				Metric for added routes (dhclient)
		leasehours leasehours
				Preferred lease time in hours (pump)
		leasetime leasetime
				Preferred lease time in seconds (dhcpcd)
		vendor vendor
				Vendor class identifier (dhcpcd)
		client client
				Client identifier (dhcpcd)
		hwaddress address
				Hardware address.

The bootp Method

This method may be used to obtain an address via bootp.

Options

		bootfile file
				Tell the server to use file as the bootfile.
		server address
				Use the IP address address to communicate with the server.
		hwaddr addr
				Use addr as the hardware address instead of whatever it really is.

The tunnel Method

This method is used to create GRE or IPIP tunnels. You need to have the ip binary from the iproute
package. For GRE tunnels, you will need to load the ip_gre module and the ipip module for IPIP tun‐
nels.

Options

		address address
				Local address (dotted quad) required
		mode type
				Tunnel type (either GRE or IPIP) required
		endpoint address
				Address of other tunnel endpoint required
		dstaddr address
				Remote address (remote address inside tunnel)
		local address
				Address of the local endpoint
		metric metric
				Routing metric for default gateway (integer)
		gateway address
				Default gateway
		ttl time
				TTL setting
		mtu size
				MTU size

The ppp Method

This method uses pon/poff to configure a PPP interface. See those commands for details.

Options

		provider name
				Use name as the provider (from /etc/ppp/peers).
		unit number
				Use number as the ppp unit number.
		options string
				Pass string as additional options to pon.

The wvdial Method

This method uses wvdial to configure a PPP interface. See that command for more details.

Options

		provider name
				Use name as the provider (from /etc/wvdial.conf).

The ipv4ll Method

This method uses avahi-autoipd to configure an interface with an IPv4 Link-Layer address
(169.254.0.0/16 family). This method is also known as APIPA or IPAC, and often colloquially referred
to as "Zeroconf address".

Options

		(No options)

IPX ADDRESS FAMILY

This section documents the methods available in the ipx address family.

The static Method

This method may be used to setup an IPX interface. It requires the ipx_interface command.

Options

		frame type
				type of Ethernet frames to use (e.g. 802.2)
		netnum id
				Network number

The dynamic Method

This method may be used to setup an IPX interface dynamically.

Options

		frame type
				type of Ethernet frames to use (e.g. 802.2)

INET6 ADDRESS FAMILY

This section documents the methods available in the inet6 address family.

The auto Method

This method may be used to define interfaces with automatically assigned IPv6 addresses. Using this
method on its own doesn't mean that RDNSS options will be applied, too. To make this happen, rdnssd
daemon must be installed, properly configured and running. If stateless DHCPv6 support is turned on,
then additional network configuration parameters such as DNS and NTP servers will be retrieved from
a DHCP server. Please note that on ifdown, the lease is not currently released (a known bug).

Options

		privext int
				Privacy extensions (RFC4941) (0=off, 1=assign, 2=prefer)
		accept_ra int
				Accept router advertisements (0=off, 1=on, 2=on+forwarding). Default value: "2"
		dhcp int
				Use stateless DHCPv6 (0=off, 1=on)
		request_prefix int
				Request a prefix through DHCPv6 Prefix Delegation (0=off, 1=on). Default value: "0"
		ll-attempts
				Number of attempts to wait for a link-local address. Default value: "60"
		ll-interval
				Link-local address polling interval in seconds. Default value: "0.1"

The loopback Method

This method may be used to define the IPv6 loopback interface.

Options

		(No options)

The static Method

This method may be used to define interfaces with statically assigned IPv6 addresses. By default,
stateless autoconfiguration is disabled for this interface.

Options

		address address
				Address (colon delimited/netmask) required
		netmask mask
				Netmask (number of bits, eg 64)
		metric metric
				Routing metric for default gateway (integer)
		gateway address
				Default gateway (colon delimited)
		media type
				Medium type, driver dependent
		hwaddress address
				Hardware address or "random"
		mtu size
				MTU size
		accept_ra int
				Accept router advertisements (0=off, 1=on, 2=on+forwarding)
		autoconf int
				Perform stateless autoconfiguration (0=off, 1=on). Default value: "0"
		privext int
				Privacy extensions (RFC3041) (0=off, 1=assign, 2=prefer)
		scope  Address validity scope. Possible values: global, site, link, host
		preferred-lifetime int
				Time that address remains preferred
		dad-attempts
				Number of attempts to settle DAD (0 to disable DAD). Default value: "60"
		dad-interval
				DAD state polling interval in seconds. Default value: "0.1"

The manual Method

This method may be used to define interfaces for which no configuration is done by default. Such
interfaces can be configured manually by means of up and down commands or /etc/network/if-*.d
scripts.

Options

		hwaddress address
				Hardware address or "random"
		mtu size
				MTU size

The dhcp Method

This method may be used to obtain network interface configuration via stateful DHCPv6 with dhclient.
In stateful DHCPv6, the DHCP server is responsible for assigning addresses to clients.

Options

		hwaddress address
				Hardware address or "random"
		accept_ra int
				Accept router advertisements (0=off, 1=on, 2=on+forwarding). Default value: "1"
		autoconf int
				Perform stateless autoconfiguration (0=off, 1=on)
		request_prefix int
				Request a prefix through DHCPv6 Prefix Delegation (0=off, 1=on). Default value: "0"
		ll-attempts
				Number of attempts to wait for a link-local address. Default value: "60"
		ll-interval
				Link-local address polling interval in seconds. Default value: "0.1"

The v4tunnel Method

This method may be used to setup an IPv6-over-IPv4 tunnel. It requires the ip command from the
iproute package.

Options

		address address
				Address (colon delimited) required
		netmask mask
				Netmask (number of bits, eg 64)
		endpoint address
				Address of other tunnel endpoint (IPv4 dotted quad) required
		local address
				Address of the local endpoint (IPv4 dotted quad)
		metric metric
				Routing metric for default gateway (integer)
		gateway address
				Default gateway (colon delimited)
		ttl time
				TTL setting
		mtu size
				MTU size
		preferred-lifetime int
				Time that address remains preferred

The 6to4 Method

This method may be used to setup an 6to4 tunnel. It requires the ip command from the iproute pack‐
age.

Options

		local address
				Address of the local endpoint (IPv4 dotted quad) required
		metric metric
				Routing metric for default gateway (integer)
		ttl time
				TTL setting
		mtu size
				MTU size
		preferred-lifetime int
				Time that address remains preferred

CAN ADDRESS FAMILY

This section documents the methods available in the can address family.

The static Method

This method may be used to setup an Controller Area Network (CAN) interface. It requires the the ip
command from the iproute package.

Options

		bitrate bitrate
				bitrate (1..1000000) required
		samplepoint samplepoint
				sample point (0.000..0.999)
		loopback loopback
				loop back CAN Messages (on|off)
		listenonly listenonly
				listen only mode (on|off)
		triple triple
				activate triple sampling (on|off)
		oneshot oneshot
				one shot mode (on|off)
		berr berr
				activate berr reporting (on|off)

KNOWN BUGS/LIMITATIONS

The ifup and ifdown programs work with so-called "physical" interface names. These names are
assigned to hardware by the kernel. Unfortunately it can happen that the kernel assigns different
physical interface names to the same hardware at different times; for example, what was called
"eth0" last time you booted is now called "eth1" and vice versa. This creates a problem if you want
to configure the interfaces appropriately. A way to deal with this problem is to use mapping
scripts that choose logical interface names according to the properties of the interface hardware.
See the get-mac-address.sh script in the examples directory for an example of such a mapping script.
See also Debian bug #101728.

SEE ALSO

ifup(8), ip(8), ifconfig(8), run-parts(8), resolvconf(8).

For advice on configuring this package read the Network Configuration chapter of the Debian Refer‐
ence manual, available at http://www.debian.org/doc/manuals/debian-reference/ch05.en.html or in the
debian-reference-en package.

Examples of how to set up interfaces can be found in /usr/share/doc/ifupdown/examples/network-inter‐
faces.gz.

相关文章

interfaces-old

参考文献

man 5 interfaces

TODO debian中/etc/network/interface文件说明


标签:used,20210329,interfaces,up,address,interface,man,name
来源: https://www.cnblogs.com/k4nz/p/14594819.html