嵌入式学习笔记9——1302时钟
作者:互联网
DS1302是通过SPI串行总线跟单片机通信的,当进行一次读写操作时最少得读写两个字节,第一个字节
是控制字节,就是一个命令,告诉DS1302是读还是写操作,是对RAM还是对CLOK寄存器操作。第二个字节
就是要读或写的数据了。
单字节读写:只有在SCLK为低电平时,才能将CE置为高电平。所以在进行操作之前先将SCLK置低电平,
然后将CE置为高电平,接着开始在IO上面放入要传送的电平信号,然后跳变SCLK。数据在SCLK上升
沿时,DS1302读取数据,在SCLK下降沿时,DS1302放置数据到IO上。
时钟寄存器0的第7位CH:时钟停止位
CH=0 振荡器工作允许 CH=1 振荡器停止
时钟寄存器2的第7位12/24: 12/24小时标志位
bit7=0 24小时模式 bit7=1 12小时模式
时钟寄存器2的第5位AM/PM: AM/PM定义
AP=0 下午模式 AP=1 上午模式
时钟寄存器7的第7位WP:写保护位
WP=0 关闭写保护 WP=1开启写保护
时钟/日历包含在7个寄存器中,数据在时钟/日历寄存
器中是二进制编码的十进制格式存储的,也就是常说
的BCD码存储的。
//单字节读写:
SCLK=0;
RST=0;
...//数据读
SKLT=1;//上升沿读取数据
SKLT=0;//下降沿放置数据
//单字节读函数
unsigned char Ds1302Read(unsigned char addr)
{ unsigned char n,dat,dat1;
SCLK=0;//先将SCLK置低电平。
_nop_();
RST=1;//然后将RST(CE)置高电平。
_nop_();
for(n=0;n<8;n++)//开始传送八位地址命令
{
DSIO=addr&0x01;//数据从低位开始传送
addr>>=1;
SCLK=1;//数据在上升沿时,DS1302读取数据
_nop_();
SCLK=0;//DS1302下降沿时,放置数据
_nop_();
}
_nop_();
for(n=0;n<8;n++)//读取8位数据
{
dat1=DSIO;//从最低位开始接收
dat=dat>>1;
dat|=dat1<<7;
SCLK=1;
_nop_();
SCLK=0;//DS1302下降沿时,放置数据
_nop_();
}
RST=0;
_nop_(); //以下为DS1302复位的稳定时间,必须的。
SCLK=1;
_nop_();
DSIO=0;
_nop_();
DSIO=1;
_nop_();
return dat;
}
//单字节写函数
void Ds1302Write(unsigned char addr,unsigned dat)
{
unsigned char n;
SCLK=0;//先将SCLK置低电平。
_nop_();
RST=1; //然后将RST(CE)置高电平。
_nop_();
for(n=0;n<8;n++)//开始传送八位地址命令
{
DSIO=addr&0x01;//数据从低位开始传送
addr>>=1;
SCLK=1;//数据在上升沿时,DS1302读取数据
_nop_();
SCLK=0;
_nop_();
}
for(n=0;n<8;n++)//写入8位数据
{
DSIO=dat&0x01;//将传进来的dat一位一位的传给DSIO
dat>>=1;
SCLK=1;//数据在上升沿时,DS1302读取数据
_nop_();
SCLK=0;
_nop_();
}
RST=0;//传送数据结束
_nop_();
}
//操作方法如下:
//1.正确安装液晶1602,请查看使用手册目录下的液晶安装方法。
//2.下载本程序
//该程序使用LCD1602显示
//3.调节液晶对比度致液晶清晰显示字符,若已调节好可跳过此步。
//4.实验板上S4键为功能键,按下后可选择调节哪个部分。
//5.S8为数字增大键。
//6.S12为数字减小键。
#include<reg52.h>
#define uint unsigned int
#define uchar unsigned char
uchar a,miao,shi,fen,ri,yue,nian,week,flag,temp,key1n;
#define yh 0x80 //第一行的初始位置
#define er 0x80+0x40 //第二行初始位置
//sbit cs1=P3^7;
//sbit ledk=P2^5;
sbit dula=P2^6;
sbit wela=P2^7;
sbit wr=P1^1;
sbit rs=P1^0;
sbit en=P2^5;
sbit SCLK=P2^1; // 6 P1.1
sbit IO=P2^0; // 7 P1.0
sbit RST=P2^4; //时钟 5 P1.2
sbit ACC0=ACC^0;
sbit ACC7=ACC^7;
sbit key=P3^7;
sbit key1=P3^0;
sbit key2=P3^1;
sbit key3=P3^2;
uchar code tab1[]={"2016-04-26 TUE"};
uchar code tab2[]={"10:32:48"};
void delay(uint xms)//延时函数
{
uint x,y;
for(x=xms;x>0;x--)
for(y=110;y>0;y--);
}
/******************液晶写入************************/
write_1602com(uchar com)//液晶写入指令函数
{
rs=0;//置为写入命令
P0=com;//送入数据
delay(1);
en=1;//拉高使能端
delay(1);
en=0;//完成高脉冲
}
write_1602dat(uchar dat)
{
rs=1;//置为写入数据
P0=dat;//送入数据
delay(1);
en=1;
delay(1);
en=0;
}
void write_sfm(uchar add,uchar dat)//写时分秒
{
uchar gw,sw;
gw=dat%10;
sw=dat/10;
write_1602com(er+add);
write_1602dat(0x30+sw);
write_1602dat(0x30+gw);
}
void write_nyr(uchar add,uchar dat)
{
uchar gw,sw;
gw=dat%10;
sw=dat/10;
write_1602com(yh+add);
write_1602dat(0x30+sw);
write_1602dat(0x30+gw);
}
void write_week(uchar week)//写星期函数
{
write_1602com(yh+0x0d);
switch(week)
{
case 1:write_1602dat('M');//delay(5);
write_1602dat('O');//delay(5);
write_1602dat('N');
break;
case 2:write_1602dat('T');//delay(5);
write_1602dat('U');//delay(5);
write_1602dat('E');
break;
case 3:write_1602dat('W');//delay(5);
write_1602dat('E');//delay(5);
write_1602dat('D');
break;
case 4:write_1602dat('T');//delay(5);
write_1602dat('H');//delay(5);
write_1602dat('U');
break;
case 5:write_1602dat('F');//delay(5);
write_1602dat('R');//delay(5);
write_1602dat('I');
break;
case 6:write_1602dat('S');//delay(5);
write_1602dat('T');//delay(5);
write_1602dat('A');
break;
case 7:write_1602dat('S');//delay(5);
write_1602dat('U');//delay(5);
write_1602dat('N');
break;
}
}
lcd_init()//液晶初始化函数
{ wr=0;
write_1602com(0x38);//设置液晶工作模式
write_1602com(0x0c);//开显示不显示光标
write_1602com(0x06);//整屏不移动,指针加一
write_1602com(0x01);
write_1602com(yh+2);//字符写入的位置
for(a=0;a<14;a++)
{
write_1602dat(tab1[a]);
//delay(3);
}
write_1602com(er+4);
for(a=0;a<8;a++)
{
write_1602dat(tab2[a]);
//delay(3);
}
}
/*********************over***********************/
/********************ds1302****************************/
void write_byte(uchar dat)
{
ACC=dat;
RST=1;
for(a=8;a>0;a--)
{
IO=ACC0;
SCLK=0;
SCLK=1;
ACC=ACC>>1;
}
}
uchar read_byte()
{
RST=1;
for(a=8;a>0;a--)
{
ACC7=IO;
SCLK=1;
SCLK=0;
ACC=ACC>>1;
}
return (ACC);
}
void write_1302(uchar add,uchar dat)
{
RST=0;
SCLK=0;
RST=1;
write_byte(add);
write_byte(dat);
SCLK=1;
RST=0;
}
uchar read_1302(uchar add)
{
uchar temp;
RST=0;
SCLK=0;
RST=1;
write_byte(add);
temp=read_byte();
SCLK=1;
RST=0;
return(temp);
}
uchar BCD_Decimal(uchar bcd)
{
uchar Decimal;
Decimal=bcd>>4;
return(Decimal=Decimal*10+(bcd&=0x0F));
}
void ds1302_init()
{
RST=0;
SCLK=0;
write_1302(0x80,miao|0x00);//允许写
write_1302(0x8e,0x00);
miao= (tab2[6]-0x30)*10+(tab2[7]-0x30);
temp=(miao)/10*16+(miao)%10;
write_1302(0x80,0x00|temp);
fen= (tab2[3]-0x30)*10+(tab2[4]-0x30);
temp=(fen)/10*16+(fen)%10;
write_1302(0x82,0x00|temp);
shi= (tab2[0]-0x30)*10+(tab2[1]-0x30);
temp=(shi)/10*16+(shi)%10;
write_1302(0x84,0x00|temp);
ri= (tab1[8]-0x30)*10+(tab1[9]-0x30);
temp=(ri)/10*16+(ri)%10;
write_1302(0x86,0x00|temp);
yue= (tab1[5]-0x30)*10+(tab1[6]-0x30);
temp=(yue)/10*16+(yue)%10;
write_1302(0x88,0x00|temp);
write_1302(0x8e,0x80);
}
void keyscan()
{
key=0;
if(key1==0)//key1为功能键
{
delay(5);
if(key1==0)
{
while(!key1);
key1n++;
if(key1n==9)
key1n=1;
switch(key1n)
{
case 1: TR0=0;//关闭定时器
//TR1=0;
write_1602com(er+0x0b);//写入光标位置
write_1602com(0x0f);//设置光标为闪烁
temp=(miao)/10*16+(miao)%10;
write_1302(0x8e,0x00);
write_1302(0x80,0x80|temp);//miao
write_1302(0x8e,0x80);
break;
case 2: write_1602com(er+8);//fen
//write_1602com(0x0f);
break;
case 3: write_1602com(er+5);//shi
//write_1602com(0x0f);
break;
case 4: write_1602com(yh+0x0f);//week
//write_1602com(0x0f);
break;
case 5: write_1602com(yh+0x0b);//ri
//write_1602com(0x0f);
break;
case 6: write_1602com(yh+0x08);//yue
//write_1602com(0x0f);
break;
case 7: write_1602com(yh+0x05);//nian
//write_1602com(0x0f);
break;
case 8:
write_1602com(0x0c);//设置光标不闪烁
TR0=1;//打开定时器
temp=(miao)/10*16+(miao)%10;
write_1302(0x8e,0x00);
write_1302(0x80,0x00|temp);//miao
write_1302(0x8e,0x80);
break;
}
}
}
if(key1n!=0)//当key1按下以下。再按以下键才有效
{
if(key2==0) //上调键
{
delay(5);
if(key2==0)
{
while(!key2);
switch(key1n)
{
case 1:miao++;
if(miao==60)
miao=0;
write_sfm(0x0a,miao);//写入新的秒数
temp=(miao)/10*16+(miao)%10;
write_1302(0x8e,0x00);
write_1302(0x80,0x80|temp);
write_1302(0x8e,0x80);
write_1602com(er+0x0b);//因为设置液晶的模式是写入数据后,指针自动加一,在这里是写回原来的位置
//write_1602com(0x0b);
break;
case 2:fen++;
if(fen==60)
fen=0;
write_sfm(0x07,fen);
temp=(fen)/10*16+(fen)%10;
write_1302(0x8e,0x00);
write_1302(0x82,temp);
write_1302(0x8e,0x80);
write_1602com(er+8);
break;
case 3:shi++;
if(shi==24)
shi=0;
write_sfm(4,shi);
temp=(shi)/10*16+(shi)%10;
write_1302(0x8e,0x00);
write_1302(0x84,temp);
write_1302(0x8e,0x80);
write_1602com(er+5);
break;
case 4:week++;
if(week==8)
week=0;
write_week(week);
write_1602com(yh+0x0f);
break;
case 5:ri++;
if(ri==31)
ri=0;
write_nyr(10,ri);
temp=(ri)/10*16+(ri)%10;
write_1302(0x8e,0x00);
write_1302(0x86,temp);
write_1302(0x8e,0x80);
write_1602com(yh+11);
break;
case 6:yue++;
if(yue==13)
yue=0;
write_nyr(7,yue);
temp=(yue)/10*16+(yue)%10;
write_1302(0x8e,0x00);
write_1302(0x88,temp);
write_1302(0x8e,0x80);
write_1602com(yh+8);
break;
case 7:nian++;
if(nian==100)
nian=0;
write_nyr(4,nian);
write_1602com(yh+5);
break;
}
}
}
if(key3==0)
{
delay(5);
if(key3==0)
{
while(!key3);
switch(key1n)
{
case 1:miao--;
if(miao==-1)
miao=59;
write_sfm(0x0a,miao);//写入新的秒数
write_1602com(er+0x0b);//因为设置液晶的模式是写入数据后,指针自动加一,在这里是写回原来的位置
//write_1602com(0x0b);
break;
case 2:fen--;
if(fen==-1)
fen=59;
write_sfm(7,fen);
temp=(fen)/10*16+(fen)%10;
write_1302(0x8e,0x00);
write_1302(0x82,temp);
write_1302(0x8e,0x80);
write_1602com(er+8);
break;
case 3:shi--;
if(shi==-1)
shi=23;
write_sfm(4,shi);
temp=(shi)/10*16+(shi)%10;
write_1302(0x8e,0x00);
write_1302(0x84,temp);
write_1302(0x8e,0x80);
write_1602com(er+5);
break;
case 4:week--;
if(week==-1)
week=7;
write_week(week);
write_1602com(yh+0x0f);
break;
case 5:ri--;
if(ri==-1)
ri=30;
write_nyr(10,ri);
temp=(ri)/10*16+(ri)%10;
write_1302(0x8e,0x00);
write_1302(0x86,temp);
write_1302(0x8e,0x80);
write_1602com(yh+11);
break;
case 6:yue--;
if(yue==-1)
yue=12;
write_nyr(7,yue);
temp=(yue)/10*16+(yue)%10;
write_1302(0x8e,0x00);
write_1302(0x88,temp);
write_1302(0x8e,0x80);
write_1602com(yh+8);
break;
case 7:nian--;
if(nian==-1)
nian=99;
write_nyr(4,nian);
write_1602com(yh+5);
break;
}
}
}
}
}
void init()
{
TMOD=0x11;
TH0=0;
TL0=0;
EA=1;
ET0=1;
TR0=1;
}
void cmg(void)//数码管锁存函数
{
dula=1;
P0=0x00;
dula=0;
wela=1;
P0=0x00;
wela=0;
}
void main()
{
cmg();//数码管锁存
lcd_init();
ds1302_init();
init();
while(1)
{
keyscan();
}
}
void timer0() interrupt 1
{
miao = BCD_Decimal(read_1302(0x81));
fen = BCD_Decimal(read_1302(0x83));
shi = BCD_Decimal(read_1302(0x85));
ri = BCD_Decimal(read_1302(0x87));
yue = BCD_Decimal(read_1302(0x89));
nian=BCD_Decimal(read_1302(0x8d));
week=BCD_Decimal(read_1302(0x8b));
//keyscan();
write_sfm(10,miao);
//write_1602com(er+0x0a);
//write_1602dat(':');
write_sfm(7,fen);
//write_1602com(er+0x07);
//write_1602dat(':');
write_sfm(4,shi);
//write_nyr(4,nian);
write_nyr(10,ri);
write_nyr(7,yue);
//write_week(week);
}
/**********************BST-V51实验开发板例程************************
* 平台:BST-V51 + Keil U3 + STC89C52
* 名称:DS1302模块实验
* 公司:深圳市亚博软件开发有限公司
* 淘宝:bstmcu.taobao.com
* 日期:2013-11
* 晶振:11.0592MHZ
* 说明:免费开源,不提供源代码分析.
******************************************************************/
#include <reg52.h>
#include "ds1302.h"
#include "display.h"
#define uchar unsigned char
unsigned char code table[]={
0x3f , 0x06 , 0x5b , 0x4f ,
0x66 , 0x6d ,0x7d , 0x07 ,
0x7f , 0x6f , 0x77 , 0x7c ,
0x39 , 0x5e , 0x79 , 0x71 ,0xbf
};
void main()
{
uchar t0,t1,t2,t3,t4,t5;
SYSTEMTIME CurrentTime;//定义了一个结构体
Initial_DS1302();
DS1302_SetTime(DS1302_HOUR,10); //设置的时间是10:54:30
DS1302_SetTime(DS1302_MINUTE,54);
DS1302_SetTime(DS1302_SECOND,30);
while(1)
{
DS1302_GetTime(&CurrentTime);
DateToStr(&CurrentTime);
TimeToStr(&CurrentTime);
t0=CurrentTime.TimeString[0];
t1=CurrentTime.TimeString[1];
t2=CurrentTime.TimeString[3];
t3=CurrentTime.TimeString[4];
t4=CurrentTime.TimeString[6];
t5=CurrentTime.TimeString[7];
display(table[t0],table[t1],table[t2],table[t3],table[t4],table[t5]);
}
}
标签:10,1602com,1302,嵌入式,write,temp,1602dat,时钟 来源: https://blog.csdn.net/NewbieJ_/article/details/109284588