MA5680T恢复出厂设置
作者：互联网
shijitianle#erase flash data ?
---------------------------------------------
Command of privilege Mode:
---------------------------------------------
Options<E><active,standby>
Active board or standby board
#第一步 清空standby数据
shijitianle#erase flash data standby ?
---------------------------------------------
Command of privilege Mode:
---------------------------------------------
<cr> Please press ENTER to execute command
shijitianle#erase flash data standby
This command will clear the standby board data has been loaded or saved
Are you sure to continue? (y/n)[n]:y
Command executes successfully, and will take effect after standby board
rebooted
shijitianle#
shijitianle#
shijitianle#
shijitianle#
#第二步 清空active数据
shijitianle#erase flash data active ?
---------------------------------------------
Command of privilege Mode:
---------------------------------------------
<cr> Please press ENTER to execute command
shijitianle#erase flash data active
This command will clear the active board data that has been loaded or saved
Please remember to backup the system configuration data
Are you sure to continue? (y/n)[n]:y
Command executes successfully, and will take effect after active board
rebooted
shijitianle#
shijitianle#
shijitianle#
#第三步 重启系统
shijitianle#reboot ?
---------------------------------------------
Command of privilege Mode:
---------------------------------------------
Options<E><system,active,standby>
System reboot or reset active board or reset standby board
shijitianle#reboot system ?
---------------------------------------------
Command of privilege Mode:
---------------------------------------------
<cr> Please press ENTER to execute command
shijitianle#reboot system
Please check whether data has saved, the unsaved data will lose if reboot
system, are you sure to reboot system? (y/n)[n]:y #输入y
shijitianle#
Platform System start ...
Memory Data Bus Test .................pass.
Memory Address Bus Test ..............pass.
Press 'Ctrl+T' To Start Memory Complete Test
Trace code : 0x00000000
Copy from ROM to RAM ...... OK!
Uncompress from ROM to RAM ...... OK!
Update fpga...OK.
Copyright (c) 1998 - 2013 by Huawei Technologies Co.,Ltd.
All Rights Reserved.
The last update date of base BIOS B is : Aug 26 2013 08:21:05
===============================================================
BOARD INFORMATION :
CPU: P2010. Processor #1.(Rev 5.01) running at 1200Mhz
1024M bytes DDR(ECC), 256M bytes flash installed on board
Baudrate of serial channel is 9600bps
Board's LAN IP address is 10.11.104.2
Board's LAN Subnet mask is 255.255.255.0
Board's LAN MAC address is 24:9E:AB:B7:9F:B1
===============================================================
Base BIOS version is 309
Save extended BIOS disable start flag...OK!
Transferring control to the extended BIOS ...OK!
System Vfs init...OK
The last update date of extended BIOS is : Mar 22 2013 17:46:38
System is booting from extended BIOS...
Extended BIOS version is 312
Press <D> key to stop auto-boot 0
Now system will boot from flash memory.
Testing Flash memory...OK!
Select area information : Program Area B ,Data Area B .
Begin to expand program... OK!
Save extended BIOS enable start flag...OK!
Transferring control to the loaded program...OK!
Starting system application init......successfully!
Starting system configuration data init...successfully!
Press any key to get started
>>User name:root
>>User password:
Huawei Integrated Access Software.
Copyright(C) Huawei Technologies Co., Ltd. 2002-2012. All rights reserved.
User root has used a default password. Change the password in time.
MA5680T>enable
MA5680T#
MA5680T#
MA5680T#display current-configuration
{ <cr>|ont<K>|port<K>|section<K>|service-port<K>|simple<K>||<K> }:
Command:
display current-configuration
Failure: The system is saving or backing up the data, please try later
这里系统启动起来，active和standby需要时间同步一下信息，所以需要等几分钟再进行操作。默认仅有的配置。
MA5680T#display current-configuration
{ <cr>|ont<K>|port<K>|section<K>|service-port<K>|simple<K>||<K> }:
Command:
display current-configuration
[MA5600V800R011: 5800]
#
[sysmode]
<sysmode>
switch adsl mode to rfc2662 vdsl mode to tr129
xpon mode switch-to profile-mode
protocol support h248
system ex-mode backup
#
[global-config]
<global-config>
event output eventid 0x023000f1
event eventlevel 0x023000f1 minor
alarm output alarmid 0x64110001
alarm output alarmid 0x64120001
ont-lineprofile gpon profile-id 0 profile-name "line-profile_default_0"
tr069-management ip-index 0
tcont 0 dba-profile-id 2
tcont 1 dba-profile-id 0
commit
quit
#
[device-config]
<device-config>
board add standby
rack info 0 description "RACK-300" name "RACK-300" manufactured-name "Huawei"
#
[public-config]
<public-config>
snmp-agent local-engineid 800007DB03249EABB79FB15A
#
[emu-config]
<emu-config>
emu add 0 fan 0 1 "H801FCBC"
#
[config]
<config>
mpls label start 8192
#
[meth]
<meth0>
interface meth0
ip address 10.11.104.2 255.255.255.0
#
[null]
<null0>
interface null0
#
[aaa]
<aaa>
aaa
authentication-scheme "default"
#
authorization-scheme "default"
#
accounting-scheme "default"
#
domain "default"
#
return标签：...,OK,system,出厂,board,设置,shijitianle,MA5680T,data 来源： https://blog.51cto.com/506554897/2445150