其他分享
首页 > 其他分享> > 双机热备

双机热备

作者:互联网

 

 

将FW_A各接口加入相应的安全区域

firewall zone trust
 set priority 85
 add interface GigabitEthernet0/0/0
 add interface GigabitEthernet1/0/5
#
firewall zone untrust
 set priority 5
 add interface GigabitEthernet1/0/0
#
firewall zone dmz
 set priority 50
 add interface GigabitEthernet1/0/6


将FW_B各接口加入相应的安全区域

firewall zone trust
 set priority 85
 add interface GigabitEthernet0/0/0
 add interface GigabitEthernet1/0/5
#
firewall zone untrust
 set priority 5
 add interface GigabitEthernet1/0/0
#
firewall zone dmz
 set priority 50
 add interface GigabitEthernet1/0/6

 

在FW_A上行业务接口GE1/0/0上配置VRRP备份组1,并设置其状态为Active
在FW_A下行业务接口GE1/0/5上配置VRRP备份组2,并设置其状态为Active

interface GigabitEthernet1/0/0
 undo shutdown
 ip address 10.2.0.1 255.255.255.0
 vrrp vrid 1 virtual-ip 10.2.0.3 active
 service-manage http permit
 service-manage https permit
 service-manage ping permit
 service-manage ssh permit
 service-manage snmp permit
 service-manage telnet permit

interface GigabitEthernet1/0/5
 undo shutdown
 ip address 10.3.0.1 255.255.255.0
 vrrp vrid 2 virtual-ip 10.3.0.3 active

 

 


在FW_B上行业务接口GE1/0/0上配置VRRP备份组1,并设置其状态为Standby
在FW_B下行业务接口GE1/0/5上配置VRRP备份组2,并设置其状态为Standby

interface GigabitEthernet1/0/0
 undo shutdown
 ip address 10.2.0.2 255.255.255.0
 vrrp vrid 1 virtual-ip 10.2.0.3 standby
 service-manage http permit
 service-manage https permit
 service-manage ping permit
 service-manage ssh permit
 service-manage snmp permit
 service-manage telnet permit

 

interface GigabitEthernet1/0/5
 undo shutdown
 ip address 10.3.0.2 255.255.255.0
 vrrp vrid 2 virtual-ip 10.3.0.3 standby

 

 

在FW_A上指定心跳口并启用双机热备功能。

hrp interface g1/0/6 remote 10.10.0.2(对端ip)

hrp enable

 

 

 

 

在FW_B上指定心跳口并启用双机热备功能。

 hrp interface g1/0/6 remote 10.10.0.1

hrp enable

 

在FW_A上配置安全策略。双机热备状态成功建立后,FW_A的安全策略配置会自动备份到FW_B上
配置安全策略,允许内网用户访问Internet

HRP_M[USG6000V1]security-policy  (+B)
HRP_M[USG6000V1-policy-security]dis this
2019-08-30 03:26:34.740
#
security-policy
 rule name permit_trust_untrust
  source-zone trust
  destination-zone untrust
  service icmp
  action permit

 

 

 


在FW_A上配置NAT策略。双机热备状态成功建立后,FW_A的NAT策略配置会自动备份到FW_B上

 

 

nat address-group group1
 section 0 1.1.1.2 1.1.1.5

 

nat-policy
 rule name policy_nat1
  source-zone trust
  destination-zone untrust
  source-address 10.3.0.0 mask 255.255.0.0
  action source-nat address-group group1

 

现在要求全网通:

AR1:

ip route-static 10.2.0.0 255.255.255.0 1.1.1.1

 LSW1;

interface Vlanif100
 ip address 1.1.1.1 255.255.255.0
#
interface Vlanif200
 ip address 10.2.0.5 255.255.255.0
#
interface MEth0/0/1
#
interface GigabitEthernet0/0/1
 port link-type access
 port default vlan 200
#
interface GigabitEthernet0/0/2
 port link-type access
 port default vlan 200
#
interface GigabitEthernet0/0/3
 port link-type access
 port default vlan 100

ip route-static 0.0.0.0 0.0.0.0 1.1.1.10

FW_A:

interface GigabitEthernet1/0/0
 undo shutdown
 ip address 10.2.0.1 255.255.255.0
 vrrp vrid 1 virtual-ip 10.2.0.3 active
 service-manage http permit
 service-manage https permit
 service-manage ping permit
 service-manage ssh permit
 service-manage snmp permit
 service-manage telnet permit
#

 

 

interface GigabitEthernet1/0/5
 undo shutdown
 ip address 10.3.0.1 255.255.255.0
 vrrp vrid 2 virtual-ip 10.3.0.3 active
 service-manage http permit
 service-manage https permit
 service-manage ping permit
 service-manage ssh permit
 service-manage snmp permit
 service-manage telnet permit
#
interface GigabitEthernet1/0/6
 undo shutdown
 ip address 10.10.0.1 255.255.255.0

firewall zone trust
 set priority 85
 add interface GigabitEthernet0/0/0
 add interface GigabitEthernet1/0/5
#
firewall zone untrust
 set priority 5
 add interface GigabitEthernet1/0/0
#
firewall zone dmz
 set priority 50
 add interface GigabitEthernet1/0/6
#
ip route-static 0.0.0.0 0.0.0.0 10.2.0.5
#

security-policy
 rule name permit_trust_untrust
  source-zone trust
  destination-zone untrust
  service icmp
  action permit
 rule name untrust_local
  source-zone untrust
  destination-zone local
  service icmp
  action permit

最后的nat策略 easy-ip:

 

LSW2:

interface GigabitEthernet0/0/1
 port link-type trunk
 port trunk allow-pass vlan 2 to 4094
#
interface GigabitEthernet0/0/2
 port link-type trunk
 port trunk allow-pass vlan 2 to 4094
#
interface GigabitEthernet0/0/3
 port link-type trunk
 port trunk allow-pass vlan 2 to 4094
#
interface GigabitEthernet0/0/4
 port link-type trunk
 port trunk allow-pass vlan 2 to 4094

 

AR1:

 

 

标签:热备,zone,service,ip,manage,permit,interface,双机
来源: https://www.cnblogs.com/mqqq/p/11434138.html